Ich habe aus Nato Posten Kepco Bipolar Powersupply gezogen und behalten..denn das ist 4 quadrant-Netzteil.
Ding ist gewichtmäßig wirklich Monster. Ding ist leider kaputt, das war glücklichsweise nur TL084, der ich durch TL054 ersetzt habe.
Vorher hat der maximale positive Spannung rausgehaut, ohne Strombegrenzung und Regelung.
4x mal Module mit 6 Transistor durchprüfen, alle ist sehr gut in Gleichtakt von Stromverstärkung.
Davor müsste ich Programmierstecker (50pol 2.54mm Platinerandstecker) basteln, danke an Henrik, wo du mir neuwertige türkise Stecker veraalt hast.
Ich habe es passend gesägt (vorher war 100 (oder sogar 120 ) polige Stecker) und geklebt. Kepco hat GPIB Option ( BIT-488B, recht alte Modelle mit State-Machine als Datenempfänger)
Den möchte ich in Betrieb nehmen und auch Platinerandstecker gut schützen und als Gehause für GPIB Buchse. -> 3D Drucker angeworfen, GPIB Buchse und 24 polige Platinerandstecker eingebaut und 1:1 durchverbinden.
Ich habe große Problem mit ihm beim GPIB Kommunikation, sobald ich Kepco einschalte, wird GPIB Bus blockiert.
Ich habe mal Keithley 182 schnell geschnappt und ich sehe da: oh 2 Leitung kämpft dagegen.
Langsam habe ich Verdacht: Kepco betreibt "Arschlochmethode"
Mit Verzweifelung in Internet gesucht, denn Kepco gibt Schaltplan nicht ohne Geld raus.
Glücklichsweise ist Kepco SN488 Manual mit Schaltplan in Internet verfügbar.
Auch wenn SN488 elektrisch ganz anders aufgebaut ist (GPIB State-machine ist es auch), nutzt SN488 gleiche GPIB-Adapterkabel wie für BOP mit eingebaute BIT-488B/D GPIB Option. (SNQ-488-1 bzw -2 heißt diese Kabeln)
Ich habe es umverdraht -> jetzt läuft es und könnte steuern. (auch Prüfung, ob ich Datenleitung vertauscht habe..-> bestanden)
Code: Alles auswählen
commando structur,
6 byte lengt,
CMMMLL
only accepted value 0x0 to 0xF, but upper nibble hasn't influced.
It means, you can send ASCII "0" to him, it would be regonizied as 0x0, because statemachine read only lower nibble.
C = command mode
MMM = Main value
LL = limit value
C command mode
0 = pos voltage full scale
1 = neg voltage full scale
2 = pos voltage 1/10 scale
3 = neg voltage 1/10 scale
4= pos current full scale
5 = neg current full scale
6 = pos current 1/10 scale
7 = neg current 1/10 scale
MMM Main value (if current mode is set -> current-value )
binary
Min value 000 = 0V
max value FFF = full scale or 1/10 scale
decimal (BCD)
min max value 000 , 999
LL (if current mode is set -> voltage value)
binary
min value 00 = 0V
max value FF = full scale or 1/10 scale
decimal (BCD)
min max 00 , 99
Da Kepco A---loch ist, bin ich mal frei, Belegung von Platinenrandstecker hier zu posten. (aus Schaltplan ins Tiefe des Internetz.)
Nur Masse (6x) und Abschirmung neben 2x "NC" ist nicht gewürfelt. -> so wird Kundenbindung erzeugt, indem man gezwungen GPIB-Kabeln mit Platinenrandstecker bei ihm zu kaufen. (Es verschärft, dass Schaltplan nicht verfügbar ist)